[John Dough]

Ok John, let spend time on this now, you have Mio Moov right? can you open regedit, and write down what you have at HKLM / init, and HKLM/Drivers / BulitIn ........ i dont have thi device, but we can do allot, if it is Just software... if you dont have regedit.exe just tell me to send you

It says not found on unit !! I have it on vista laptop okay do not see any init in HKLM though.

Frake I found it on HKLM/init : depend30 reg_binary 14 00
depend60 reg_binary 14 00
launch20 REG_SZ device.exe
Launch30 REG_SZ gwes.exe
Launch60 REG_SZ services.exe
Launch9999 REG_SZ \My Flash Disk\Mio...

HKLM Drivers : Active
block device
builtin
console
pccard
pccmia
resources
sdcard
unimodem
usb


Any help?

Ok John, let spend time on this now, you have Mio Moov right? can you open regedit, and write down what you have at HKLM / init, and HKLM/Drivers / BulitIn ........ i dont have thi device, but we can do allot, if it is Just software... if you dont have regedit.exe just tell me to send you

It says not found on unit !! I have it on vista laptop okay do not see any init in HKLM though.

i sent you PM,, answer it we leave this threat to other... let work out side this threat
LOL.. regedit .exe mean file for wince5 to put in inside your intern device and run it inside the device...

Works for me in all IGOs 8 Amigo/Primo you must have the wrong files mate.

I have the right files, they work fine on iGo8 8.3.2.xxxx which is what I was using before I changed to Primo.

Works for me in all IGOs 8 Amigo/Primo you must have the wrong files mate.

I have the right files, they work fine on iGo8 8.3.2.xxxx which is what I was using before I changed to Primo.

Ok friend,, if you dont like my first suggustion to make all in one file,, then try this

open your save file
open system.ini if you have [POI] then check if you have this,, if not then add them all
[poi]
sort_order_save="Restaurant,Accomodation,Petrol_Station,Parking,Medical"
priority_save=""
sort_order="Restaurant,Accomodation,Petrol_Station,Parking,Medical"
priority=""

download this and add it to save folder.
http://hotfile.com/dl/70100257/fe471d0/poi_visiblities.txt.html

report the result

Do you mean this is the same
::::::::::::::::::::::::::::::::::::
device_settings
-----------------

[Default]
gps port open=true
gps port=COM2
gps baud rate=57600
gps default protocol is nmea=true
gps sirfbinary protocol=false
gps sirfbinary baud rate=57600
gps protocol switch=false
gps use sirf clm=true
gps cold start=false
gps use rx flag=true
gps reset watchdog timeout=15000
gps hot start cmd=$PSRF101,0,0,0,0,0,0,12,1
gps warm start cmd=$PSRF101,0,0,0,0,0,0,12,2
gps cold start cmd=$PSRF101,0,0,0,0,0,0,12,4
dpgs off cmd=$PSRF111,0
dgps waas cmd=$PSRF111,1
dgps egnos cmd=$PSRF111,1
dgps msas cmd=$PSRF111,1
tmc port open=true
tmc port=COM1
tmc baud rate=14400
tmc duplex mode=true
tmc gns module=false
tmc command timeout=100
tmc command retry=3
MapCacheSizeMin=8388608
MapCacheSizeMax=8388608
MinStoragePage=900
screen dump key=195
volume=50
one2one port open=false
one2one port=1
one2one baud rate=115200
bluetooth hardware available=false
warning battery percentage=15
min usb brightness=0
max usb brightness=100
BigMallocBound=8192

[HWVersion=100]
gps port=VSP1
gps use sirf clm=false
gps use rx flag=false
gps reset watchdog timeout=0

[GPS=ATHEROS]
gps port open=true
gps port=VSP1
gps baud rate=57600
gps default protocol is nmea=true
gps sirfbinary protocol=false
gps sirfbinary baud rate=57600
gps protocol switch=false
gps use sirf clm=false
gps cold start=false
gps use rx flag=false
gps reset watchdog timeout=0
gps hot start cmd=$PUNV,START,HOT
gps warm start cmd=$PUNV,START,WARM
gps cold start cmd=$PUNV,START,COLD
dpgs off cmd=$PUNV,CONFIG,SBAS,OFF
dgps waas cmd=$PUNV,CONFIG,SBAS,ON
dgps egnos cmd=$PUNV,CONFIG,SBAS,ON
dgps msas cmd=$PUNV,CONFIG,SBAS,ON

[quote="nitro"]Do you mean this is the same
::::::::::::::::::::::::::::::::::::
device_settings
-----------------

No friend, send me PM your MSN so we talk out

Ok friend,, if you dont like my first suggustion to make all in one file,, then try this

open your save file
open system.ini if you have [POI] then check if you have this,, if not then add them all
[poi]
sort_order_save="Restaurant,Accomodation,Petrol_Station,Parking,Medical"
priority_save=""
sort_order="Restaurant,Accomodation,Petrol_Station,Parking,Medical"
priority=""

download this and add it to save folder.
http://hotfile.com/dl/70100257/fe471d0/poi_visiblities.txt.html

report the result

That part of system.ini was already there, I added the txt file replacing the one that was there, still no change, however.

i sent you PM,, answer it we leave this threat to other... let work out side this threat
LOL.. regedit .exe mean file for wince5 to put in inside your intern device and run it inside the device...

Please keep us up to date.
I'm also struggling with the TMC under Moov 360 with external kit.

btw, in order to keep this thread (sort of) organized, you can use the following thread:
viewtopic.php?f=718&t=60947
Someone already opened it but couldn't get an answer.

[caubecari]

I have a problem everytime I open Igo it says global_cfg not found please help me thanks

Does anyone besides myself have issues with Primo freezing (at the opening boot screen) when coming out of sleep mode? It can be running along just fine, but (for example) if I stop for more than, say, 5 minutes (with no motion) then the screen goes blank (and the device - a Mio C520 - goes to sleep). When I attempt to bring it out of SLEEP mode the opening blue-ish screen appears but there is no action in the progress bar.

The same type of behavior occurs if I force SLEEP mode (by momentarily pressing the POWER button).

Is there a way to disable SLEEP mode entirely in the C520? Not a desirable solution, but maybe the only one unless someone has a clever SYS.TXT directive I don't know about.

I have a problem everytime I open Igo it says global_cfg not found please help me thanks

Check your sys path at sys.txt.
global_cfg.zip should not unzip it, leave it as it is zip format.

Does anyone besides myself have issues with Primo freezing (at the opening boot screen) when coming out of sleep mode? It can be running along just fine, but (for example) if I stop for more than, say, 5 minutes (with no motion) then the screen goes blank (and the device - a Mio C520 - goes to sleep). When I attempt to bring it out of SLEEP mode the opening blue-ish screen appears but there is no action in the progress bar.

The same type of behavior occurs if I force SLEEP mode (by momentarily pressing the POWER button).

Is there a way to disable SLEEP mode entirely in the C520? Not a desirable solution, but maybe the only one unless someone has a clever SYS.TXT directive I don't know about.

i think you need to clean your device and make new install of Primo.
search also in mobilesim, there are user who add sys.txt for your mio brand solve the brightiness and some power issue.

aLL THE LINKS FOR 800X480 are dead .

Can someone re-up please please

[John Dough]

I have a problem everytime I open Igo it says global_cfg not found please help me thanks

Delete everything in your sys.txt and use this one.

[device]
type="Mio 370"




[tts]
tts_min_ready_wav=1
tts_getaway_time=100
tts_expected_engine_delay=400
;turn_penalty_multiplier=90 ;(100)

[feature]
text_guidance=1
signpost_coloring=1
tmc_event_coloring=1
tmc_traffic_side=1
ding=0



[gps]
protocol="NMEA"
port=2
baud=57600
change the port /baud to suit you.

[John Dough]

Ok John, let spend time on this now, you have Mio Moov right? can you open regedit, and write down what you have at HKLM / init, and HKLM/Drivers / BulitIn ........ i dont have thi device, but we can do allot, if it is Just software... if you dont have regedit.exe just tell me to send you

Frake I found it on HKLM/init : depend30 reg_binary 14 00
depend60 reg_binary 14 00
launch20 REG_SZ device.exe
Launch30 REG_SZ gwes.exe
Launch60 REG_SZ services.exe
Launch9999 REG_SZ \My Flash Disk\Mio...

HKLM Drivers : Active
block device
builtin
console
pccard
pccmia
resources
sdcard
unimodem
usb


Any help? JD