[quote="John Dough"]

complete please this to the end
Launch9999 REG_SZ \My Flash Disk\Mio... ?

and write down here your register at
HKEY_LOCAL_MACHINE\Drivers\BuiltIn\TMC_HWCOM
"DevConfig"=hex:\....?
"DeviceArrayIndex"=dword:...... ?

""FriendlyName"="TMC_COM" ? correct
"IClass"="{.......????????? }"
"Index"=......?

"Irq"=.....?
"MemBase"=dword:50004000
"MemLen"=dword:00000030
"Order"= ........?
"Prefix"="COM" ...? correct?
"Priority"=dword:00000000 ... correct?
"Tsp"=......?

do you have also in your register HKEY_LOCAL_MACHINE\Drivers\BuiltIn\SW_TMC ??

please answer all together

[John Dough]

complete please this to the end

Here you go

Launch9999 REG_SZ \My Flash Disk\MioAutorun\Launch.exe
and write down here your register at
HKEY_LOCAL_MACHINE\Drivers\BuiltIn\TMC_HWCOM
"DevConfig"=hex:\(25length binary value)
"DeviceArrayIndex"=dword:00000002 (2)
""FriendlyName"="TMC_COM" ? correct YES
"IClass"="{CC5195AC-BA49-48a0-BE17-DF6D-1B0... }"
"Index"=00000001 (1)

"Irq"=0000000F (15)
"MemBase"=dword:5000800 (1342210048)
"MemLen"=dword:00000030 (48)
"Order"= 0000000 (0)
"Prefix"="COM" ...? correct? YES
"Priority"=dword:00000000 (0)
"Tsp"=......? NOT THERE

do you have also in your register HKEY_LOCAL_MACHINE\Drivers\BuiltIn\SW_TMC ?? NO not there

OK


please answer all together

complete please this to the end

Here you go

Launch9999 REG_SZ \My Flash Disk\MioAutorun\Launch.exe
and write down here your register at
HKEY_LOCAL_MACHINE\Drivers\BuiltIn\TMC_HWCOM
"DevConfig"=hex:\(25length binary value)
"DeviceArrayIndex"=dword:00000002 (2)
""FriendlyName"="TMC_COM" ? correct YES
"IClass"="{CC5195AC-BA49-48a0-BE17-DF6D-1B0... }"
"Index"=00000001 (1)

"Irq"=0000000F (15)
"MemBase"=dword:5000800 (1342210048)
"MemLen"=dword:00000030 (48)
"Order"= 0000000 (0)
"Prefix"="COM" ...? correct? YES
"Priority"=dword:00000000 (0)
"Tsp"=......? NOT THERE

do you have also in your register HKEY_LOCAL_MACHINE\Drivers\BuiltIn\SW_TMC ?? NO not there

OK


please answer all together

please try this Tip

your sys.txt [TMC} make the port 1 and baud 38400

in the folder of Primo

rename all this file

atmc_ce.dll (to) atmc_ce_BAK.dll

GPSTMC.DLL (to) GPSTMC_BAK.DLL

TMCGPS.DLL (to) TMCGPS_BAK.DLL
use GPSTMC.DLL from miomap forexample v.3.3 91Kb

Here are 11 versions from the Gpstmc.dll

Good luck with trying

Code: Select allhttp://www.mediafire.abc/?096nc37za8s73tf

change abc to com

EDIT on 19-9-10 now 11 versions (old 9) and refresht the link

Here are 9 versions from the Gpstmc.dll

Good luck with trying

Code: Select allwww.mediafire.abc/?btjj17ubydu8dxg

change abc to com

good work kener

the one gpstmc v4.0.10.1-C.dll were reserved to miomap..

[caubecari]

I have a problem everytime I open Igo it says global_cfg not found please help me thanks

Delete everything in your sys.txt and use this one.

[device]
type="Mio 370"




[tts]
tts_min_ready_wav=1
tts_getaway_time=100
tts_expected_engine_delay=400
;turn_penalty_multiplier=90 ;(100)

[feature]
text_guidance=1
signpost_coloring=1
tmc_event_coloring=1
tmc_traffic_side=1
ding=0



[gps]
protocol="NMEA"
port=2
baud=57600
change the port /baud to suit you.

Thanks but right now I have another message say my resolution 480x272 is not support. I just got it working by enter the following line to sys
[interface]
resolution_dir="320_240"

[rawdisplay]
highres=0
screen_x=320
screen_y=240
stretch=1

Greetings my friends.

I've tried but i couldn't find option in IGO PRIMO where i can calculate route from point A to point B (where point A ISN'T current GPS position), something like start point --> finish point that have other nav. software like MIREO ViaGPS etc.

Can you help me where is that option "hidden"?

Thanks for your quick answer.

Best regards
SIMCHEE

Greetings my friends.

I've tried but i couldn't find option in IGO PRIMO where i can calculate route from point A to point B (where point A ISN'T current GPS position), something like start point --> finish point that have other nav. software like MIREO ViaGPS etc.

Can you help me where is that option "hidden"?

Thanks for your quick answer.

Best regards
SIMCHEE

Easy.
select menu option "Edite Route."
click on the blue flag on the line "current gps position"

THAT'S IT

Thank you!

can someone give me a link to download the full content of primo with german tts?
thanks

I have a question myself. My device is HTC Kaiser. If I start the navigation it says "detecting GPS receiver". I tried to add to the sys.txt:
[gps]
port=4
baud=4800
but then it stop already at the startup screen.

Maybe someone can help me out. Thx

i think your GPS should be so
[gps]
port=4
baud=57600

Thanks, but this doesn't work either. Still stuck at startup screen. I will have to soft reset each time I try. Someone help?

NO ONE CAN UPLOAD 480*800(wvga) files?

NO ONE CAN UPLOAD 480*800(wvga) files?

+1

[John Dough]

Here are 9 versions from the Gpstmc.dll

Good luck with trying

Code: Select allwww.mediafire.abc/?btjj17ubydu8dxg

change abc to com

good work kener

the one gpstmc v4.0.10.1-C.dll were reserved to miomap..

That dll is not in the zip do you have it Frake?

Here are 9 versions from the Gpstmc.dll

Good luck with trying

Code: Select allwww.mediafire.abc/?btjj17ubydu8dxg

change abc to com

good work kener

the one gpstmc v4.0.10.1-C.dll were reserved to miomap..

That dll is not in the zip do you have it Frake?

it is in the zip