[mmdpiti]

http://www.tomasii.cdc.cz/iGO8/navody/PPATH/ppath+sys_C720_(navod_003).zip
------------------------------

I created program files directory.I introduced the ppath.txt and when I made miomap doesn't run
I made it igo8.exe in miomap folder like in your picture.
I don't know how it works at you

[Twingo]

Guys this topic is all about igo 8, not miomap.

[mmdpiti]

Guys this topic is all about igo 8, not miomap.

It's not about miomap it's about igo8 to work on the mio devices !!!

[Twingo]

well it runs on my mio

I created program files directory.I introduced the ppath.txt and when I made miomap doesn't run
I made it igo8.exe in miomap folder like in your picture.
I don't know how it works at you

This is what you need ( You will never need another miomap.exe.id...). Check the readme files; You may want to change some script files, depending what is your folder structure ( in this configuration I use 2 different versions of IGO, you can change the script to use only one).If you just want to launch IGO8 in place of MIO, you don't need the "launcher", change miomap.scp script file.

http://www.uploadjockey.com/download/2199712/MIOMAP.rar

[mmdpiti]

This is the checksum for IGO8 8.3.2.64873: 0f 9f 6d ef fb a4 a4 03 86 b7 d8 00 !!!
I want checksum for IGO8 8.3.2.71348 ???
Or what program can fiind the checksum of a file ???

I succeded in version IGO8 8.3.2.64873 and I attached miomap.exe.id

[mmdpiti]

I created program files directory.I introduced the ppath.txt and when I made miomap doesn't run
I made it igo8.exe in miomap folder like in your picture.
I don't know how it works at you

This is what you need ( You will never need another miomap.exe.id...). Check the readme files; You may want to change some script files, depending what is your folder structure ( in this configuration I use 2 different versions of IGO, you can change the script to use only one).If you just want to launch IGO8 in place of MIO, you don't need the "launcher", change miomap.scp script file.

http://www.uploadjockey.com/download/2199712/MIOMAP.rar

The method is too difficult and I choosed the easyest one
The easyest is to rename the file IGO8.exe in MioMap.exe in MIOMAP folder and to create the new file MioMap.exe.id with checksum from IGO8.exe

[mmdpiti]

well it runs on my mio

With my method it's runs on MIO Cx20 (C320, C520, C720)

[mmdpiti]

I want checksum (24 chars) for IGO8 8.3.2.71348 ???
Or what PROGRAM can find the checksum (24 chars) of a file ???

Who are the settings for MIO C720 ???
PLEASE ............

P.S.
I rename IGO8.EXE to MioMap.exe and I think missing miomap.exe.id

go to:
viewtopic.php?f=257&t=24898&hilit=miomap.exe.id
and find the solution.

have fun
plony

I try and doesn't WORK !!!

you have to produce a new miomap.exe.id by the method i mention previously.

it should work perfectly!!

plony

mmdpiti is NOT need to make miomap.exe.id. You MUST have the following structure of folders: \SDMMC\Miomap\-and HERE you must have the exe. Modify the sys.txt according with this path and will be ok.
You change the miomap 3.2 with iGO8 - that must be made with a 1:1 folder structure.

Hello every one I tried to install it on my s300 or DOPOD, but doesn't work.
1;put the whole file on the sd Card in a file, launched igo.exe = will not work.
2:Put the files separately on SD card = will not work either.
3;Down loaded igo 8.3.2.7 separately on Sdcard and then added languages,maps to the content separately = it then starts , ask for other contents=then launches and then blocks, any suggestions

Thanks

dsman

Dopod / S300 wm 6.1 CV+Oggi

Here is an update on the "off-road" lock-up issue I've been having... I've tried some recommendations that folks have suggested on this board, but to no avail...

However, I think I have narrowed down the problem a little... I've found that the lockup only seems to occur ONLY if your device obtains a GPS signal while in the "off-road" area. If you already have a GPS signal when you reach the off-road location, the lock-up does NOT occur, even when going from the off-road position back to the road again.

However, if you turn your device on while at the off-road location, wait to obtain a GPS signal and then drive close enough to a road that iGo thinks you are on the road, that is when the lockup occurs.

I get this error with the UK TeleAtlas map but I don't get the error if I also add the "WestEUMAJOR.fbl" major roads of Europe map to the map folder !!!

Previously I was not including the major roads map since I had included all the other maps and thought it unnecessary.

I have only tested this from one off road location and so it may not work from other locations.

I'm using IGO 8 R3 on my Touch HD. Works fine the Kikker skin works to. But with and without the skin from Kikker my IGO is 20/30 meters behind. I have it isnatld on my srotage card. Because it is 160MB. Is there a way to solve this problem?

[mmdpiti]

you have to produce a new miomap.exe.id by the method i mention previously.
it should work perfectly!!
plony

It doesn't work !!!
It tells me I have: "some missing files" !!!
Here is the MD5 (checksum) to miomap.exe (IGO8.exe): FA5E5E87212E8741C18FF33FC53B1E6C !!!
Can you convert checksum from 32 chars in 24 chars ???
Or at least tell me what PROGRAM give me checksum for 24 chars OR converts from 32 to 24 chars ???