Already have a "total commander" in my Omnia,and the "Igo8" Icon created in "programs" menu,but ...

Still nothing
The Icon exist,but the same message "database not found" .

I will delete everything from my device,and will download from here again. viewtopic.php?f=256&t=46621&start=840

Hope it is a good link.

May be the solution for me is to get only pda version?

Hi jetmouse,

Mio c320 (480x272). I was getting 2 MSND related FFUIERRORs with the original data and iGo would quit. With the fixed data, I'm getting one FFUIERROR pop-up, but iGo still loads after dismissing the pop-up:

FFUIERROR: Unknown object identifier
Identifier=[vMSNDKeyPageShown]
Script "[Unamed]" command 0

Thanks for your continued great work,
titanium180

[monkey12]

Did you know if TMC is supported by iGO on Navigon 8110 device ?
I'm tried COM1@38400,GNS (like Navigon) but nothing works. Maybe my licence file don't support TMC ?

Possibly Navigon doesn't use the GNS protocol on these PNA devices any more? Also any other protocols, iGO comes with, won't match.

with LZF data.zip works perfectly...

Hi.

I fresh install the lastest version (8.3.2.91972) but the speedcam (17/05/2009) doesn't work.

I already put the .txt file on the correct directory (content\speedcam). The igo takes a time on "Init... warning data" on the first run, but into the warning menu don't appear the speedcam option.
Anyone test this version with speedcams?

tks

Just decide where to go (even if it's demo mode) and you will see all! You must have itinerary on!

Hmmm...
I finally resolved the issue by using the set supplied by shaq89.

I had this issue a LONG time ago, and it WAS resolved by renaming the file etc. For some reason it didn't work this time.
But bottom line, it seekms OK now. I'll test everything later today.

Thanks.

There is a possibility for an incompatible 2577 folder, but I'm not sure about that.

This must be a joke, because it doesn't make any sense

[Twingo]

And where did you get that picture from ?

Please...i need some help because i get many error messages (no voice, no language, could load 800x480.bmp....blahblah) and igo never starts...

i need a small dummies guide for installing the may28 version of igo on my Touch HD in german...pleas help me

thnk you so much

[mmdpiti]

--== img ==--
This must be a joke, because it doesn't make any sense

It's new IGO8 version !!!

Hi.

I fresh install the lastest version (8.3.2.91972) but the speedcam (17/05/2009) doesn't work.

I already put the .txt file on the correct directory (content\speedcam). The igo takes a time on "Init... warning data" on the first run, but into the warning menu don't appear the speedcam option.
Anyone test this version with speedcams?

tks

Just decide where to go (even if it's demo mode) and you will see all! You must have itinerary on!

make a rute from A to B and then flyover, back in cursor menu and the speedcams menu appears, or wait to conect to satelite.

Hi jetmouse,

Mio c320 (480x272). I was getting 2 MSND related FFUIERRORs with the original data and iGo would quit. With the fixed data, I'm getting one FFUIERROR pop-up, but iGo still loads after dismissing the pop-up:

FFUIERROR: Unknown object identifier
Identifier=[vMSNDKeyPageShown]
Script "[Unamed]" command 0

Thanks for your continued great work,
titanium180

You have 2 ways to resolve this...

1º)Open the data.zip (from old version) the go at \ui_igo8\480_272\ui copy the file: msnd_480_272.ui
Open the data.zip (new version) then replace msnd_480_272.ui at \ui_igo8\480_272\ui with the old version.

Or

2º) Or you can just replace the new data.zip with the older.

I make the 1º and this resolve my problem...

Regards,
Cleiton

--== img ==--
This must be a joke, because it doesn't make any sense

It's new IGO8 version !!!

How are you so sure ?

How can there be a difference of more than 10,000 in the both build numbers, if they were built on the same day ?
Even when iGO Amigo came out, its build number continued iGO8 R3 with a difference that reflected time logically.

And where did you get that picture from ?

'Bandiboy' posted it here first on page 316 of this post.
The picture was taken from this url: http://kepfeltoltes.hu/090605/809575252 ... es.hu_.jpg

For people with 480x272 resolution, I found a great solution for the error problems. I used the March 2nd version I was using and just swapped out the license folder and the Igo8.exe from the May 28th version and it works excellent. I tried the data.zip with the latest upload from JM, but still got errors when changing the skin, so I went back to the data.zip from the March 2nd "NEXT" release and I also had to delete the save folder. No errors and it runs even faster than before. No new bugs and one noticeable bug fix.... no more parking lot bug as of yet. I haven't had it freeze at all in any of the known places it would lock up before because of that bug. Finally seems Nav-N-Go went in the right direction. Thanks for this release JM and others. I was reluctant since the March 10th and April 3rd releases seems to be more buggy than previous releases, but I am very happy not to have that parking lot freeze issue anymore.... well at least not as of yet with 3 days of constant use. Now if NNG ever come up with a solution for the wake-up problem then I think they would have finally nailed this whole Igo8 thing.

Hi.

I fresh install the lastest version (8.3.2.91972) but the speedcam (17/05/2009) doesn't work.

I already put the .txt file on the correct directory (content\speedcam). The igo takes a time on "Init... warning data" on the first run, but into the warning menu don't appear the speedcam option.
Anyone test this version with speedcams?

tks

Just decide where to go (even if it's demo mode) and you will see all! You must have itinerary on!

make a rute from A to B and then flyover, back in cursor menu and the speedcams menu appears, or wait to conect to satelite.

That works, thanks!!!