thanks ladgaz i ll try and keep you all posted...

[andis]

Did anyone get this working for Navigon 2100T with MioPocket 2? I have tried different versions (2much's, DMANN's fix) but can't get it to work. Application launches fine but then after a couple of minutes, I get a popup info message that people have mentioned earlier in this thread (CThorDevice::ResetDevice). Initially I was getting this error message a few seconds after MN7 would start. Once I added TTS sound files, error message started popping up a little later (a couple of minutes) after application launch.

If anyone can help me get it working, I'll appreciate it very much. Thanks.

Have you tried solution on post #27 ?
It worked for me

thanks ladgaz i ll try and keep you all posted...

Have a Loox N110 TMC and the software Navigon 7.4.0 runs like a charm, hehe.
If you need help, please contact me.

On Loox N1xx either the PanoramaView 3D- Version or the TMC-Version works.

As written in many topics, it's not possible to have both in one software on a unit with 320 x 240.

The Advantage of that software in gsmfree-forum is, that you can install it on Loox N1xx and run it from the mainscreen-button "Navigator"

But be aware that it takes a longer time for the cab to install on Loox N1xx.

So be patient and don't interrupt the installation-process, although nothing really exciting happens on the screen during installation.

I run the software desktop-free with a customized startscreen, where i can choose MN7.4.0 with PanoramaView 3D or alternatively MN7.4.0 with TMC Pro.

Good luck.

Ladgaz

@2much.
Hi.
I installed on my Navigon3110 version MN7.4, I had to change the folder in NAVIGON MN6, and the file NAVIGON.EXE in MN6.exe.
Now the law and all the GPS, when I try on the street with no destination all is well, when, instead enter a destination it should be very slow, it seems that it blocks.

Through him, I solved the problem by itself, thanks to the DMANN x sw.

Can I use in Indonesia ? Thanks

Did anyone get this working for Navigon 2100T with MioPocket 2? I have tried different versions (2much's, DMANN's fix) but can't get it to work. Application launches fine but then after a couple of minutes, I get a popup info message that people have mentioned earlier in this thread (CThorDevice::ResetDevice). Initially I was getting this error message a few seconds after MN7 would start. Once I added TTS sound files, error message started popping up a little later (a couple of minutes) after application launch.

If anyone can help me get it working, I'll appreciate it very much. Thanks.

Have you tried solution on post #27 ?
It worked for me

Thanks a lot. That fixed the problem. I guess I didn't try it earlier thinking that its for PDAs. Thanks again.

Thanks to many of you guys, I have MN7.4 loaded and running on my Navigon2100. However, it seems that MN7.4 is not talking to GPS chip. I dont get any GPS signal. When I check GPS status, everything is just blank. Even the GPS clock is blank. Is there a port or something like that which I have to change to make it talk to internal GPS chip? Thanks for any help.

Thanks to many of you guys, I have MN7.4 loaded and running on my Navigon2100. However, it seems that MN7.4 is not talking to GPS chip. I dont get any GPS signal. When I check GPS status, everything is just blank. Even the GPS clock is blank. Is there a port or something like that which I have to change to make it talk to internal GPS chip? Thanks for any help.

You must set the port and baudrate.
In UserSetting:
<GPS>
<type> 2 </ Type>
<GPSPort> 2 </ GPSPort>
<Baudrate> 57600 </ Baudrate>
<DRVPrefix> </ DRVPrefix>
</ GPS>

##############################
In CoreConfig:
[Default Sensor Gps Serial]
ConnectionType = 1
Port = 2
Baudrate = 57600
TimeOut = 5

Try varying the number of attempts and the Port Baudrate.

Does anybody has this release working with POI-Warner ?
I've just bought POI-Warner and seems doesn't work with this release, maybe i have some setting wrong and have to make more test...
But if someone has it working some hints can be very useful...

Thanks to many of you guys, I have MN7.4 loaded and running on my Navigon2100. However, it seems that MN7.4 is not talking to GPS chip. I dont get any GPS signal. When I check GPS status, everything is just blank. Even the GPS clock is blank. Is there a port or something like that which I have to change to make it talk to internal GPS chip? Thanks for any help.

You must set the port and baudrate.
In UserSetting:
<GPS>
<type> 2 </ Type>
<GPSPort> 2 </ GPSPort>
<Baudrate> 57600 </ Baudrate>
<DRVPrefix> </ DRVPrefix>
</ GPS>

##############################
In CoreConfig:
[Default Sensor Gps Serial]
ConnectionType = 1
Port = 2
Baudrate = 57600
TimeOut = 5

Try varying the number of attempts and the Port Baudrate.

Thanks for pointing me in the right direction. I was able to change these settings and get it to work.

Just for the benefit of anyone who faces similar problem, the settings for Navigon 2100 are

Connection Type = 2
Port = 1
Baudrate = 4800

@garfield207

I am glad that you've solved the problem, we in the forum makes us useful.

Hello!

I downloaded the Files from the first post, copied them to my SD-Card, changed my GPS-Settings in the Config files and everything is fine. My position is found via GPS, i can take a look on my map and so on.. but, when i start navigation (real or simulated) the program ends and i am back on my windows today screen. No error message or else..
Has somebody out there an idea what problem my PDA has?

Thx, Maik

To have 3dterrain:
...during my experiments i have "mixed" the two version.....:try to put TmcHal.dll,audioin.dll,vocon3200api.dll,vocon3200rsrc.dll,navigon.exe in the navigon folder and Terrain_EU.nfs in map folder(from the 7310 version)....and use MapDrawer.nfs from the 7310 "Update FIX 13.04.09"by 2much if you want different color of the terrain....
maybe another way to have the 3d terrain is simply to use all the 7310 version with the "MobileNavigator.res" from 2310(it could be what i have do during my mad mix!!!!).....hope it can help you...!!

@arcatarc

Well, I followed your instructions and I have installed what you said on my Navigon 3110 (Sw MN7.4.0 5110 to DMANN), but we do not believe it works.
For now I only see the map where I am and there's a cape, then try to check in the street.

Thanks

Hello!

I downloaded the Files from the first post, copied them to my SD-Card, changed my GPS-Settings in the Config files and everything is fine. My position is found via GPS, i can take a look on my map and so on.. but, when i start navigation (real or simulated) the program ends and i am back on my windows today screen. No error message or else..
Has somebody out there an idea what problem my PDA has?

Thx, Maik

@ MaikP

You should at least tell us the browser you have, just to understand, so we could help.

@ MaikP

You should at least tell us the browser you have, just to understand, so we could help.

I don't know, what "browser" means.
I have an HTC Trinity P3600 with cooked Win 6.1.
Navigon 7.3.1 worked also, but i got problems with my memory, so it crashed every 5 minutes.