yes, tmc doesn't work. thats the only bad point

@carodiavolo
you emntioned you have an version with panoram view wich is very slow. can you perhaps upload this version, i would like to try it.

thanks

I installed Navigon on my Mio P350.
I have a problem. When I get to the opening screen
it stays on for a few moments then cloces down so I
can't get any further????
I was hoping someone may have had a similar problem and
got it fixed. And could tell me how to get me over my problem.

Please help I need it???
EAH

@falco953: look some pages back in the same thread for 3d...

@estimaster: there is a warning about batteries ? Look in the first page of the thread...

hi,

thanks carodiavolo, this version works really fine on my navigon 2100 (without max).

Also the Standby works now!!!!!

what did you change to get it running on the 2100? It freezes at my 2100 after the start sequence?

Für navigon 5110 (3100;2100,2110;5100 And similar devices mit autorunce 320*240) no MAX

MN7 7.4.0 PNA Final build 789
Navigon Mobile Navigator 7.4.0 for resolution 320x240
Requirements: PNA WinCE 5.0

The program without MAP
SD ready
http://rapidshare.com/files/236422984/M ... .part1.rar
http://rapidshare.com/files/236418142/M ... .part2.rar
Pass: DMANN


Here only programs without NFS files
http://rapidshare.com/files/236464245/MN7LETZTE.rar
Pass: DMANN

All functions simply work to copy all on a flash card
tmc works

Before first start CoreConfig.ini and UserSettings. Default his TmC-Gps port and baud rate customize... Other data program write automatic (old and xml datei)

As always I have added automatic start of the program ( autorunce ) and automatic increase in working memory...

Maps
http://stealth.to/?id=ynn4skxmd4t2gwu3b ... azdmnr2a2f
These are cards Q1 2009 v2 and only with them SW will work...

this 789 version vorking wery nice on my Mio c250, without memory problems. thanks carodiavolo

denba, in my device, when run Navigon, always ask for configuration (language, kilometres, etc...) and when shut down the device with the simbol "power off" and after I made a hard reset always as for the configuration. Why? (no save my changes and my preferences). Thanks for you help

Für navigon 5110 (3100;2100,2110;5100 And similar devices mit autorunce 320*240) no MAX

MN7 7.4.0 PNA Final build 789
Navigon Mobile Navigator 7.4.0 for resolution 320x240
Requirements: PNA WinCE 5.0

The program without MAP
SD ready
http://rapidshare.com/files/236422984/M ... .part1.rar
http://rapidshare.com/files/236418142/M ... .part2.rar
Pass: DMANN


Here only programs without NFS files
http://rapidshare.com/files/236464245/MN7LETZTE.rar
Pass: DMANN

All functions simply work to copy all on a flash card
tmc works

Before first start CoreConfig.ini and UserSettings. Default his TmC-Gps port and baud rate customize... Other data program write automatic (old and xml datei)

As always I have added automatic start of the program ( autorunce ) and automatic increase in working memory...

Freezes on my 2100 Your other Version didn´t. Any idea? I already changed the GPS-Settings in coreconfig.ini and UserSettings.Default!

1.Is it possible to install PoiWarner 3 for MN7 on a PNA device? (GoClever 3550A with WinCE 5.0). I need this in order to add Speed Cameras to MN7.4. Or there is another way to do it?

I bought an original version a couple of weeks ago of that crappy software and have no way to make it work on my chinese+7.4
Trashed.

2.As I see MN7.4b789 is reposted from Gulli (great board too !! I have had to learn German ). If after copying to the SD card the program starts in German could someone write down how to change the language to English? Please write the German words as they will appear first.
Thank you for your help !

Is not too difficult, there are the icons

Q1.Yes, I could agree it is a bit srappy this program PoiWarner. BUT:
Can you suggest other way to import (use) speed cameras in MN7.4 ?
Just to clarify that the ones provided with MN7 does not cover many parts of Europe.

Q2. O.K. I am not so close with German as you even I would like to.
This is what I see when starting MN7.4 b789 on GoClever2550A (WinCE 5.0) with a map in the respective folder.
(also have other programs so I am using a menu too).
All In German:
Start>WarningScreen>Menu:
NeuesZiel;MeineZiel;NachHause;KarteAnzeigen.
And at the bottom: Optionen.
When press Optionen:
RoutenPlanung;Einstelungen;Productinformationen;GPS Status;Notfallhilfe.
When press Einstelingen:
(and at the bottom) Optionen:
Auslieferungszustand.(WarningScreen), and then:
I got an errorMessage:
CThorDevice:ResetDevice.
After this the unit restarts and start in the menu I am using to manage all the applications in the PNA.
Another issue is when I press the ShutOff button tne program (MN7) shuts, but the unit too.
And I wanted to shut down the program, but not teh unit. I would like after shutting down the program to get back in the menu of the unit.

What you could suggest?

Für navigon 5110 (3100;2100,2110;5100 And similar devices mit autorunce 320*240) no MAX

MN7 7.4.0 PNA Final build 789
Navigon Mobile Navigator 7.4.0 for resolution 320x240
Requirements: PNA WinCE 5.0

The program without MAP
SD ready
http://rapidshare.com/files/236422984/M ... .part1.rar
http://rapidshare.com/files/236418142/M ... .part2.rar
Pass: DMANN


Here only programs without NFS files
http://rapidshare.com/files/236464245/MN7LETZTE.rar
Pass: DMANN

All functions simply work to copy all on a flash card
tmc works

Before first start CoreConfig.ini and UserSettings. Default his TmC-Gps port and baud rate customize... Other data program write automatic (old and xml datei)

As always I have added automatic start of the program ( autorunce ) and automatic increase in working memory...

@DMANN:
I have tried your release too.
I got the same error as posted above.
Just to note I have started teh prog in manually clicking mn7.exe.
E.g. I have no idea how to use the autorunce.exe. I have put it in the Navigon folder, -nothing. On the SD root: nothing. Then I did the start manually.

Autorunce is used on genuine Navigon GPS to automatically start up the software. If you don't have Navigon GPS, don't bother with it, run it through Navigon.exe.

Q1.Yes, I could agree it is a bit srappy this program PoiWarner. BUT:
Can you suggest other way to import (use) speed cameras in MN7.4 ?
Just to clarify that the ones provided with MN7 does not cover many parts of Europe.

Speedcams and Poi management are the biggest problem in Navigon
For my country (Italy)are enough good and updated so I can use the original ones...
Buy i agree that the adding of Pois and Speedcam is impossible and could be a reason to switch to another navigation software

Q2. O.K. I am not so close with German as you even I would like to.
This is what I see when starting MN7.4 b789 on GoClever2550A (WinCE 5.0) with a map in the respective folder.
(also have other programs so I am using a menu too).
All In German:
Start>WarningScreen>Menu:
NeuesZiel;MeineZiel;NachHause;KarteAnzeigen.
And at the bottom: Optionen.
When press Optionen:
RoutenPlanung;Einstelungen;Productinformationen;GPS Status;Notfallhilfe.
When press Einstelingen:
(and at the bottom) Optionen:
Auslieferungszustand.(WarningScreen), and then:
I got an errorMessage:
CThorDevice:ResetDevice.
After this the unit restarts and start in the menu I am using to manage all the applications in the PNA.
Another issue is when I press the ShutOff button tne program (MN7) shuts, but the unit too.
And I wanted to shut down the program, but not teh unit. I would like after shutting down the program to get back in the menu of the unit.
What you could suggest?

At This moment I've only a PDA version so is difficult to follow exactly step by step what you are making....
But after pressing Einstellung, if you press

Optionen>Auslieferungszustand

means that you ask to the unit "Revert to default values"
After tapping for the first time

Optionen

if i recall correctly you have to press the first voice of the screen.. maybe "Allgemein"

About CThorDevice:ResetDevice and unit restarts when pressing Shutoff see post #20 about ExitBehaviourCodes in ApplicationSettings.xml and discover wich ones fits better on your device...

this 789 version vorking wery nice on my Mio c250, without memory problems. thanks carodiavolo

denba, in my device, when run Navigon, always ask for configuration (language, kilometres, etc...) and when shut down the device with the simbol "power off" and after I made a hard reset always as for the configuration. Why? (no save my changes and my preferences). Thanks for you help

I´m change in AplicationSettings.xml line:
<ExitBehaviour>4</ExitBehaviour> ,
in CoreConfig.ini lines:
[Default Sensor Gps Serial]
ConnectionType=2
Port=2
BaudRate=4800
TimeOut=5
in userSettings.default lines:
<GPS>
<Type>2</Type>
<GPSPort>2</GPSPort>
<Baudrate>4800</Baudrate>
<DRVPrefix />
</GPS>
after this changes all working without problems.

@DMANN:
I have tried your release too.
I got the same error as posted above.
Just to note I have started teh prog in manually clicking mn7.exe.
E.g. I have no idea how to use the autorunce.exe. I have put it in the Navigon folder, -nothing. On the SD root: nothing. Then I did the start manually.

If you start with MN7.exe that should increase worked memory manually!!!

What device for you?

@DMANN:
I have tried your release too.
I got the same error as posted above.
Just to note I have started teh prog in manually clicking mn7.exe.
E.g. I have no idea how to use the autorunce.exe. I have put it in the Navigon folder, -nothing. On the SD root: nothing. Then I did the start manually.

If you start with MN7.exe that should increase worked memory manually!!!

What device for you?

What map do you use, my map europ q1 2009 doesn't wordk with this version

[2much]

oly this map Maps eu Q1-09 for build 789 <<< you can use