[quote="calimero0007"][quote="brtroi"]The new release of the POI-Warner with the keygen works very fine now on MobileNavigator 6 in 3D mode, all POIs are seen (and not only in 2D mode).

Hello
I have a problem with Poi Warner It does not work - it bug to the approach of a POI with MN6 in 2D and 3D. Have a you solution
It is installed in the PDA
Excuse yourself my English but I use a translator

Thanks

Do you use the latest release (it's in the start post) with the keygen? If you are not sure, please download it again.

ok, i test[/quote]

Hello
I download again the last release and i install in my PPc , but it don't work-
At approach a poi (speed camera) MN6 return and bug in the "poi warner "windows -
Please help me
thx[/quote]

Hello,
I found with Forum GPSPASSION the solution to make walk Poi Warner. It is necessary to transform the BMP of the icons of the radars into 16 colors 24 bits to 256 colors 8 bits and all functions working in 2D and 3D
thx

thanks for the replies will give it ago
did wonder if it was something along them lines
thanks again

arf

[brtroi]

Radar POI D-A-CH 2007-01-14

added to start post.

hy guys i have a problems with nm6 when I start the software it does not safeguard my parameters I am obliged to start again each time
please help
thanks

Hi, falks, I have tried everything, install from dvd, put manually what is necessary into my SD card... I also did a hard reset just in case...
No matter what I do, Navigon6.exe runs, then it stops and my upper "bar" where is written "logo windows, Démarrer and so on disappears, become black, and I have to perform a soft reset.
As someone got Mn6 running fine with hx4700 wm5 french. Please, tell me point by point exactly what procedure...
No problem with tomtom 6 and Igo 2006, both are running fine.
Thinks for your help

You realy sure that you have MN6 for pocket pc not for PNA ?

Unfortunatly YES !

hy guys i have a problems with nm6 when I start the software it does not safeguard my parameters I am obliged to start again each time
please help
thanks

I take it u mean favorites etc, using a card reader check the files are not read only

Hi om my A201 I have set this configuration during the installation or on gps configuration:
-GPS Baudspeed: 4800
-GPS device: GPS_HWCOM

Good luck

1st of all...thanks for that great Major-Release. It works fine on my Ipaq hw6515 with Windows 2003 SE.
But unfortunately it will not save my settings on my Ipaq hw6915 (windows 5). And of course I installed the 05.cab first!
So each time I start MN6 on my hw6915 all my sttings are gone (Language, GPS, Home-adress etc)

Any idea to fix that problem?

Many thx in adv.

MdS

1st of all...thanks for that great Major-Release. It works fine on my Ipaq hw6515 with Windows 2003 SE.
But unfortunately it will not save my settings on my Ipaq hw6915 (windows 5). And of course I installed the 05.cab first!
So each time I start MN6 on my hw6915 all my sttings are gone (Language, GPS, Home-adress etc)

Any idea to fix that problem?

Many thx in adv.

MdS

Put your Storage Card into your card reader and remove the write protection of these files:
NaviLib.ini
GPSTMCInfo.ini
Settings-Folder (complete folder)

SpecialK

[brtroi]

Radar POI D-A-CH 2007-01-19

added to the start post.

can anyone please give me a link of the cracked exe in rapidshare. I have problems downloading from megaupload

[brtroi]

can anyone please give me a link of the cracked exe in rapidshare. I have problems downloading from megaupload

I added a mirror in the start post.

thanx a lot pal